{"slug": "building-a-robotic-hand-on-a-budget", "title": "Building a Robotic Hand on a Budget", "summary": "Maker Mahdi built an 18-degree-of-freedom 3D-printed robotic hand and forearm for under $300 in parts, using servo motors housed in the forearm that drive joints via thin steel-rope tendons running through PTFE tubes. Each tendon passes through its joint's center of rotation to keep tendon path length constant, and a coiled flat ribbon cable with a printed guide replaces a slip ring for the rotating arm base. The project addresses dexterity, which the source notes remains a stubbornly hard problem because hardware capable of fine motor movement is often expensive.", "body_md": "For all the recent advances in robot control enabled by machine learning, there are still a few problems which remain stubbornly difficult: locomotion, for example, or whole-body balance for humanoids. Dexterity, in particular, has emerged as a particularly hard problem, requiring both software and hardware sophistication; hardware capable of useful fine motor movement is often quite expensive. [Mahdi]’s been working on that problem, though, with an [eighteen-degree-of-freedom robot hand](https://www.youtube.com/watch?v=Sk0x-xMNQks) that costs less than $300 in parts.\n\nAlthough the hand is the main point of the project, it’s really a full forearm. The skeleton is 3D printed and driven by servo motors; like a human hand, the motors are located mostly in the forearm and use tendons to actuate the joints. Unlike most servo-driven robot hands, it uses thin steel rope instead of synthetic fiber cables, which eliminates the need to tie small knots — the tendon can simply be tensioned and crimped in place.\n\nTo reduce friction, each tendon runs through a PTFE tube. Wherever a tendon would have to go past a joint, it passes through the joint’s center of rotation, which keeps the length of the tendon’s path from changing as the joint bends. Each finger on the hand can move side-to-side and flex two joints independently.\n\nThe base of the arm can also rotate on a servo motor, which made powering the servo motors a challenge: the servos draw too much current for small slip-rings, and larger slip-rings were too expensive. Since the arm didn’t need to rotate continuously, though, he instead used a coil of flat ribbon cable which winds in or our as the joint rotates, with a printed cable guide to keep it from kinking; not only is this much cheaper than a slip ring, it’s also more compact.\n\nWe’ve [seen a few](https://hackaday.com/2018/10/18/mechatronic-hand-mimics-human-anatomy-to-achieve-dexterity/) robot hands take the same [tendon-based approach](https://hackaday.com/2026/10/05/building-a-cheap-dexterous-robot-hand/) before, and the [more realistic ones](https://hackaday.com/2023/03/16/robot-hand-looks-and-acts-like-the-real-thing/) replace the servo motors with [artificial muscles](https://hackaday.com/2021/10/28/taking-a-stroll-down-uncanny-valley-with-the-artificial-muscle-robotic-arm/). Some have even 3D-printed [tendons and ligaments](https://hackaday.com/2023/11/16/robot-hand-has-good-bones/).", "url": "https://wpnews.pro/news/building-a-robotic-hand-on-a-budget", "canonical_source": "https://hackaday.com/2026/11/21/building-a-robotic-hand-on-a-budget/", "published_at": "2026-11-22 06:00:20+00:00", "updated_at": "2026-11-22 06:13:10.073096+00:00", "lang": "en", "topics": ["robotics"], "entities": ["Mahdi", "Hackaday"], "also_reported_by": [], "takeaway": "Route each tendon through its joint's center of rotation so the tendon path length stays constant as the joint bends, and replace an expensive slip ring with a coiled flat ribbon cable plus a printed guide when the joint doesn't rotate continuously.", "recommendation": null, "alternates": {"html": "https://wpnews.pro/news/building-a-robotic-hand-on-a-budget", "markdown": "https://wpnews.pro/news/building-a-robotic-hand-on-a-budget.md", "text": "https://wpnews.pro/news/building-a-robotic-hand-on-a-budget.txt", "jsonld": "https://wpnews.pro/news/building-a-robotic-hand-on-a-budget.jsonld"}}